Capability Assets

Creates a potential secondary-material supply route for industrial and battery applications that require rare-metal products while seeking to reduce reliance on primary mineral extraction.

Enables evaluation of machined C/C composite parts for fixtures and rotating components operating under high-temperature heat treatment, where metallic components can deform or degrade.

Addresses the thermal-management constraint of high-density AI and GPU server deployments by removing heat from the complete server assembly rather than relying only on air cooling or chip-level cold plates.

Addresses machining-stage delamination, fiber breakout, tool wear, and conductive dust risks when a composite part requires complex geometry and controlled finishing after molding.

Provides a route for buyers that need lightweight CFRP parts but require a small supplier able to discuss design, mold preparation, autoclave cure, and trimming rather than only purchase raw composite material.

Addresses CO2 removal from gas streams where gas upgrading or hydrogen purification requires a potentially lower-energy alternative to bulk thermal separation.

Addresses the logistics constraint of transporting hydrogen by using liquefiable ammonia as a carrier and separating hydrogen at the point of use for fuel or supply applications.

Addresses accelerated battery degradation and separator shrinkage risk in high-temperature operation, where conventional polyolefin separators may not wet with viscous high-temperature electrolytes.

Supports operations that cannot accommodate long battery charging interruptions by enabling short opportunity-charge windows and high power input/output for industrial mobile equipment.

Provides a custom liquid-cooling component option where high heat loads cannot be managed by an air-cooled heat sink and the part must fit a defined device or equipment envelope.

Addresses fraying, interlayer delamination, abrasive tool wear, and conductive fine dust that can impair CFRP part quality and machining-equipment reliability.

Reduces cement-related emissions in factory-made drainage, retaining-wall and other infrastructure products while preserving a regional precast production route.

Anode makers need spherical natural-graphite powder with high packing density, low specific surface area and low oil absorption compared with flake, at a stated fixed-carbon level of 99.9% or higher.

Chinese export controls and supply limits on expandable graphite disrupt flame-retardant building products and graphite heat-spreader sheet; a second Asian source with Japanese specification control is needed.

High-conductivity Al/Cu jackets are hard to melt-weld or braze without porosity, slag, or whole-part overheating; lid-thickness variation after finishing also creates hot spots. The shop mills channels and FSW-seals the lid on one hybrid machine, then press-corrects warp so the lid thickness (path from coolant to the heat-source face) is uniform.

Imported CDUs and racks for direct liquid cooling arrive with mixed foreign connection standards that Japanese air-conditioning brass practice does not stock, delaying loop build-out. A single stainless-valve shop that also prefabricates spools can match those ends and kit valve-plus-pipe modules.

Filled TSV/TGV wafers and glass coupons leave Cu proud of the dielectric; without CMP the next wiring level cannot be patterned at package density.

Open plated vias block fine build-up and create reliability voids; a printable, grindable fill that accepts cap plating lets the board return to a flat, via-free surface.

Sintered magnets are limited to simple block/arc shapes, chip easily, often need grinding, and lock the design to a high rare-earth sintered grade. Plastic-magnet injection is used when the buyer needs complex 3D geometry, thin walls, insert-molded metal, lower inertia, or a ferrite-bonded option that does not depend on sintered NdFeB.

Bonding a magnet to a cover, shaft or gear adds assembly labor, adhesive-strength inspection and positional scatter. Two-shot / insert molding is used when the buyer wants the magnet and neighboring structure as one molded unit with tool-controlled alignment.

Applications that cannot take NdFeB (cost, corrosion, or rare-earth supply) still need a directional sintered ferrite with custom machining. This line is a Japan-made ferrite source that also finishes the part and can co-press ceramic, so the buyer is not limited to catalog blocks.

Sites that need a hydrogen-rich reducing atmosphere (or a compact on-site source of H2+N2) can feed handled liquid/gaseous ammonia into a dissociator instead of storing large volumes of bottled hydrogen.

Creates a route from CFRP waste to usable compound and molded products, targeting lower virgin-fiber demand and applications where metal or virgin-fiber composite cost constrains adoption.

Silica fume is import-dependent and blast-furnace slag supply is shrinking as steelmaking shifts; a domestic natural pozzolan is needed that can replace part of cement without a new placement method.

Fuel-cell stacks need end terminals that both collect current and seal hydrogen, oxidant and coolant paths; joining dissimilar metals/thicknesses without warpage-induced leak paths is a production bottleneck.

Allows battery developers to test electrode materials and coating conditions without committing to a full production-scale coating line.

Reduces positional variation and operator burden during low-volume pouch-cell and lithium-ion prototype-cell assembly.

Targets conductivity, electrolyte transport, high-voltage degradation, and silicon-anode expansion constraints in high-performance lithium-ion cells.

Recovers constrained metals from mixed or low-concentration industrial waste streams that are difficult to process with a single conventional route.

Provides a route to fabricate dimensionally controlled custom components from ceramics and refractory metals when conventional machining or fusion welding would compromise heat resistance, plasma resistance or material integrity.

Supports delivery of heavy custom structures and equipment where large dimensions, high-strength or stainless steel, welded fabrication and subsequent machining must be coordinated by a regional supplier.

Conventional Haber-Bosch ammonia synthesis requires high temperature and high pressure (classically hundreds of °C and multi-MPa to tens of MPa), driving energy use, CO2 intensity when powered by fossil heat/compression, and barriers to smaller or renewable-coupled plants. Precious-metal (e.g. Ru) alternative catalysts raise cost and supply-chain concentration risk.

Lab-scale advanced ammonia catalysts often stall before industrial use because IP, process engineering, and catalyst manufacturing sit in different organizations. Fuel-ammonia projects need a clear path from catalyst science to plant-integrable catalyst supply.

Enables small-lot, high-precision CFRP components for semiconductor manufacturing equipment, medical imaging devices, and aerospace where dimensional stability, vibration damping, and X-ray transparency are required but metal is unsuitable.

Reduces cement demand and embodied CO2 in ready-mix and precast concrete by mineralizing injected CO2, without compromising structural performance.

Eliminates or delays manual crack repair in reinforced concrete, cutting maintenance CO2 and extending service life beyond conventional 65-year design life.

Enables low-cost, low-energy CO2 recovery from ambient air and industrial exhaust using a honeycomb-structured sorbent that can be regenerated with waste heat (150-500°C), avoiding the degradation and volatility issues of amine-based absorbents.

Provides complete stack hardware for SOFC/SOEC developers and system integrators that lack in-house ceramic/metal stack assembly capability, reducing time-to-prototype.

Prevents cathode performance degradation caused by Cr evaporation from ferritic stainless steel interconnects at 700-800°C, maintaining low ASR and long stack life.

Enables precise insulation and series interconnection in thin-film perovskite modules while minimizing dead-area width, which is critical to module efficiency and yield.

Portland cement production accounts for ~8% of global CO2. Cemenon eliminates cement entirely, using industrial byproducts (fly ash, metakaolin) polymerized with alkali solution. High acid resistance solves sewer corrosion, a major infrastructure cost driver.

Ultra-high-purity hydrogen (>99.9999%) is required for advanced semiconductor manufacturing (2 nm node, power devices), fuel-cell vehicles (H2 stations), and medical uses, but conventional Pd-alloy membrane purifiers are expensive due to palladium cost (~5,000/kg) and supply constraints. Vanadium is ~1/100th the cost with comparable theoretical H2 selectivity. However, vanadium membranes have historically suffered from hydrogen embrittlement and oxidation. UHP's VASA alloy formulation and module design claim to solve these durability issues.

Pouch cell tab leads must provide a hermetically sealed electrical feedthrough between the cell interior (organic electrolyte) and external circuit, while withstanding the cell assembly heat-seal process and long-term exposure to electrolyte. Improper tab lead design causes electrolyte leakage, cell degradation, and fire risk. Standard off-the-shelf tab leads do not accommodate the wide variety of cell capacities, form factors, and current ratings required by custom pouch cell projects.

Perovskite R&D labs struggle to evaluate ink formulations at small scale because production slot-die coaters require large ink volumes and commercial inkjet printers lack solvent resistance for perovskite precursors. PerovsJet bridges the gap with 0.5 mL minimum ink volume and full chemical resistance.

Conventional lithium recovery from brine requires large solar evaporation ponds (months to years, weather-dependent, high water loss) or solvent extraction with chemical-intensive processes. This adsorbent enables selective lithium capture in a compact DLE process with no added chemicals for elution.

Traditional data center cooling (air conditioning) becomes insufficient for high-density AI GPU racks (>40 kW/rack). Operators need a complete liquid cooling infrastructure — not just cold plates — including heat rejection, pumping, water treatment, and commissioning. Most lack in-house liquid cooling engineering expertise.

The complexity and yield risk of managing separate vendors for TGV drilling, seed layer deposition, copper plating, and finishing in glass core substrate production for AI advanced packaging.

The difficulty of forming high-quality, crack-free TGV micro-vias in glass substrates for advanced semiconductor packaging, particularly the trade-off between positional accuracy, via profile control, and substrate damage.

The difficulty of producing crack-free TGV vias and precision cavities in varied glass compositions, especially for non-standard glasses where conventional laser-only or standard etching processes produce suboptimal results.

The complexity and cost of conventional TGV formation that requires laser modification + wet etching (multi-step, wet chemistry, environmental waste). Simpler direct laser drilling could reduce the process chain and eliminate chemical handling.

Eliminates supply-chain and price volatility risk from rare-earth elements (Nd, Dy, Tb) by creating a permanent magnet from iron and nitrogen, the most abundant elements, while targeting magnetic performance comparable to NdFeB magnets.

Enables compact, complex-shaped permanent magnets with tailored multi-pole magnetization patterns (radial, pole-anisotropic, convergent) for high-precision sensors and miniaturized motors, while offering rare-earth-free material options.

Conventional Haber-Bosch economics favor very large centralized plants; lower T/P synthesis reduces vessel and compressor requirements so ammonia can be made onsite at hundreds to tens of thousands of tonnes per year where H2 and N2 (or power for their production) are available.

Industrial and fertilizer users face shrinking domestic ammonia capacity and volatile import prices; onsite modules produce only the needed volume where hydrogen/nitrogen utilities exist, cutting dedicated transport and storage infrastructure.

Users need a stable reducing/protective atmosphere without bulk hydrogen logistics; cracking liquid or vapor NH3 onsite yields a controllable H2-rich mixed gas with low residual ammonia and low dew point after drying.

Semiconductor, chemical, and industrial processes emit NH3-bearing exhaust or stripped ammonia gas that must be abated without generating large secondary NOx/N2O loads; compact catalytic destruction units address leak and stripping streams up to percent-level concentrations.

Overseas buyers of precision CFRP components — especially for semiconductor equipment, wind energy, and medical devices — typically must coordinate separately with a resin formulator, a design house, a molder, and a machinist. This fragmented supply chain multiplies qualification cost, lead time, and IP exposure risk.

Standard prepreg systems from major suppliers (Toray, Hexcel) are optimized for aerospace structural properties but do not address application-specific constraints like flame/smoke/toxicity for public transit, chemical resistance for semiconductor wet processes, or fast-cure cycles for high-volume consumer-electronics production. Customers requiring specialty resin properties must either develop them in-house or work with multiple suppliers.

Reducing the clinker factor in concrete without sacrificing strength or durability is the primary lever for cutting construction embodied carbon, but supplementary cementitious materials (fly ash, slag, silica fume) face supply constraints and regional availability limits. Silica White offers a natural-pozzolan alternative sourced from domestic volcanic deposits.

Construction demolition waste (concrete-ga ra) constitutes a major waste stream, and conventional recycling produces aggregate that still has a net carbon footprint from crushing and transport. CO₂-Nomicom converts the calcium-rich cement paste fraction into a CO₂ sink via accelerated carbonation, producing a carbon-negative recycled aggregate that can replace virgin crushed stone in civil engineering applications.

Conventional amine solution scrubbing requires high energy for regeneration, equipment corrosion management, and pre-drying of gas streams. This solid absorbent operates efficiently under high relative humidity without pre-drying, and its weaker CO2 bond enables desorption at lower temperature, reducing total capture energy and cost.

Enables small-scale, decentralized CO2 capture from point sources without the capital and footprint of large amine scrubbing towers. Suitable for demonstration, R&D, and small industrial, commercial, or agricultural sites needing on-site CO2 recovery.

Enables long-term (>40,000h) SOFC/SOEC stack operation by preventing Cr-poisoning of cathode and limiting contact resistance increase from oxidation on metal interconnectors at high operating temperature.

Metal springs relax and creep at SOFC/SOEC operating temperatures above 600°C, causing loss of stack compression, increased contact resistance, and gas leakage. Ceramic springs maintain elastic force at up to 1000°C in both air and hydrogen atmospheres.

Provides compact, on-site hydrogen generation without alkaline electrolyte handling, enabling direct coupling with renewable power sources for green hydrogen production at laboratory, industrial, or mobility scales.

Enables precision etching of thick (1.0 mm+) stainless steel fuel-cell alloys to form gas distribution channels and flow fields for SOFC/SOEC stacks, maintaining surface flatness critical for stack sealing while allowing custom flow-path geometries.

Conventional rolled copper foil for Li-ion battery anodes is limited to ~8µm minimum thickness before handling becomes impractical (tearing, wrinkling). Thinner foil could reduce battery weight and material cost, but thin copper alone is too fragile. Teikoku Ion's composite approach uses a polymer film substrate for mechanical strength while plating ultra-thin copper layers for conductivity, breaking the thickness barrier.

Conventional Li-ion batteries with organic-solvent electrolytes are flammable, volatile, swell in vacuum, freeze at low temperature, and fail at high temperature. This limits applications in space, aviation, desert solar, and medical devices. The ionic liquid electrolyte (molten salt, room-temperature liquid) eliminates volatility and flammability while maintaining wide-temperature operation.

Conventional Li-ion battery cathode manufacturing uses PVDF binder dissolved in NMP (N-methyl-2-pyrrolidone), a toxic, flammable organic solvent requiring expensive solvent recovery systems and posing worker safety and environmental risks. PowerBinder enables water-based cathode slurry processing, eliminating NMP entirely.

Perovskite solar module manufacturing requires P1/P2/P3 patterning of transparent electrode, charge transport, and perovskite layers with micron precision across large areas. Substrate thermal expansion and layer shrinkage during processing cause misalignment, reducing active area. NITTOKU KYOTO's patented (JP5329505) stretch-compensation and contour-following technology enables <20µm dead-zone patterning, maximizing module efficiency in roll-to-roll production.

Enables solar power generation on curved, lightweight or portable surfaces where traditional silicon panels are too heavy or inflexible.

Reduces variability in lab-scale perovskite cell fabrication and enables prototyping of flexible film-type devices without large-scale vacuum equipment.

High-density, low-loss vertical interconnects in glass interposers for integrating optics close to ASICs in CPO, addressing bandwidth, power, and thermal density in AI servers.

Scalable formation of dense vertical interconnects in large glass panels for cost-effective glass-core substrates used in co-packaged optics and high-density AI packaging.

Conventional TSV or organic substrates suffer from higher parasitic capacitance, thermal mismatch, or outgassing in miniaturized RF/MEMS and 3D packaged devices for AI edge or sensor modules.

Wafer-scale TGV limits panel-level manufacturing economics and throughput for high-volume advanced packaging in AI servers or high-density interconnects; organic cores lack the flatness and low-loss benefits of glass.

Elevated embodied carbon in standard precast concrete for civil and infrastructure applications.

EV battery terminals require intricate non-axisymmetric shapes with zero burrs, high precision, and durability under thermal/vibration stress, which traditional machining or simple stamping cannot achieve cost-effectively at volume.

Conventional interconnects suffer from oxidation, Cr evaporation, and poor thermal cycling performance in high-temperature electrolysis/fuel cell environments, raising reliability and cost barriers for SOEC deployment.

High energy penalty and cost of conventional DAC sorbents for capturing dilute atmospheric CO2; need for materials enabling simpler regeneration without high heat.

Need for low-carbon alternatives to standard precast retaining walls and barriers in projects with sustainability or net-zero targets, especially in disaster-prone or rural settings.

Metal or filament-wound pipes are heavy, corrosion-prone or limited in length/diameter; buyers need lightweight, high-precision tubular structures for industrial rotating or structural uses.

Conventional carbon fiber tows are thick and difficult to drape or impregnate uniformly in complex or thin composite layups, limiting design freedom and increasing defects.

Manufacturers of sensors, stepping motors, and magnetic couplings face volatile pricing and supply risk for rare-earth magnets (NdFeB, SmCo). Ferrite magnets offer low cost but also low magnetic performance. Alnico magnets avoid rare earths but are expensive (high Ni and Co content) and cannot be rolled into thin shapes. Fe-Cr-Co magnets fill the gap: zero rare earths, zero nickel, higher Br than ferrite, and rollable into sheet as thin as ~0.5 mm.

Global dependence on China-sourced rare earths (Nd, Dy, Tb) for permanent magnets creates supply-chain risk, price volatility, and geopolitical vulnerability for EV, wind turbine, and industrial motor manufacturers. MAGesty reduces or eliminates rare-earth content while remaining compatible with existing bonded-magnet production lines.

Need for lightweight, high-strength, corrosion-resistant structural or functional components in harsh chemical or mechanical environments where metals fail due to weight or corrosion.

High embodied carbon in conventional precast concrete for infrastructure and urban projects; need for drop-in low-carbon alternatives using local industrial byproducts without major process changes.

Embodied carbon from cement in public infrastructure secondary products; requirement for verifiable low-carbon alternatives compatible with existing construction practices and government green procurement.

Large footprint, high infrastructure needs, and centralized nature of conventional DAC plants limit deployment in urban, small-scale, or on-site CO2 supply scenarios.

High-temperature operation and Cr-poisoning/oxidation degradation in conventional SOEC stacks limit durability and increase system costs for decentralized or modular hydrogen production.

Traditional portable storage suffers from long charge times, short lifespan, high self-discharge, and failure in extreme temperatures, making them unreliable for emergency or continuous industrial use.

High capital and energy intensity of conventional large-scale centralized ammonia plants; high logistics costs and boil-off for transporting ammonia or hydrogen over long distances; barriers to using renewables for ammonia production at smaller scales or remote sites.

Metal trays/fixtures deform, oxidize or require frequent replacement under extreme heat and cycling; heavy weight increases energy use and handling costs.

Need for lightweight, high-strength, corrosion-resistant structural or containment components that metal or standard plastics cannot satisfy under weight, strength or chemical constraints.

Requirement for wear-resistant, lightweight functional components (rollers, fasteners, bobbins) in fiber/textile machinery or general equipment where standard metals or plastics wear quickly or add excessive weight.

Need for lightweight, high-strength, corrosion-resistant tubular components in small batches where filament winding equipment is oversized or inflexible.

Requirement for maintenance-free sliding parts in high-temperature, lubricant-free, or chemically aggressive environments where metal or standard plastics fail.

Need for cost-effective, circular-economy CFRTP materials that maintain performance while incorporating recycled content for automotive and industrial lightweighting.

High CO2 emissions from conventional cement-intensive concrete in infrastructure projects under decarbonization mandates.

High material cost and supply constraints of silver paste in electrode formation for solar cells and battery-related electronics.

Developers require precise, independent measurement of SOEC efficiency under non-standard gas compositions or with tracer methods to validate reaction mechanisms and durability before scaling.

Developers of modular or decentralized e-methane / green hydrogen systems need small-to-medium scale SOEC stacks that operate at lower temperatures with reduced Cr poisoning and custom form factors without relying on major stack suppliers.

R&D teams developing SOEC components or systems lack access to high-temperature test rigs capable of realistic steam/CO2 mixtures and power levels, delaying iteration cycles.

High capital cost and logistics barriers of centralized large-scale ammonia plants prevent local production in resource-limited or remote regions; long supply chains increase fertilizer and energy-carrier costs.

Producing complex busbar assemblies that combine high electrical conductivity with structural lightweighting and thermal management in space-constrained EV or industrial power modules.

Delivering ready-to-install lightweight structural or functional CFRP components without requiring the buyer to coordinate multiple specialized vendors for composites work.

Manual layup of UD tape for complex fiber architectures is slow, inconsistent and costly for low-to-medium volume production of high-performance thermoplastic composites.

High energy cost and large footprint of conventional liquid-amine or solid-sorbent DAC systems limit deployment scale for industrial CO2 utilization or storage.

Hard-to-abate sectors need carbon-neutral gaseous fuels compatible with existing natural gas infrastructure without full electrification.

Centralized hydrogen production and long-distance transport create high costs, losses, and supply vulnerabilities for regional decarbonization.

Addresses need for higher-efficiency solar modules at scale by combining perovskite top cell with silicon bottom cell in large-area formats while improving durability for commercial deployment.

Reduces manufacturing cost and equipment complexity for perovskite solar cells while enabling arbitrary patterning and size customization for non-standard installations and IoT/power applications.

Enables installation of solar generation on weight-limited or curved surfaces (metal roofs, building facades) where rigid silicon panels cannot be used due to load or shape constraints.